Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations TugboatEng on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!
Ordinate dimension in Sketch environment?
- Thread starter azonic3d
- Start date
JohnRBaker
Mechanical
No, Ordinate Dimensions are NOT supported in the Sketcher task.
John R. Baker, P.E.
Product 'Evangelist'
Product Design Solutions
Siemens PLM Software Inc.
Cypress, CA
To an Engineer, the glass is twice as big as it needs to be.
John R. Baker, P.E.
Product 'Evangelist'
Product Design Solutions
Siemens PLM Software Inc.
Cypress, CA
To an Engineer, the glass is twice as big as it needs to be.
- Thread starter
- #4
JohnRBaker
Mechanical
There are no plans that I'm aware of.
John R. Baker, P.E.
Product 'Evangelist'
Product Design Solutions
Siemens PLM Software Inc.
Cypress, CA
To an Engineer, the glass is twice as big as it needs to be.
John R. Baker, P.E.
Product 'Evangelist'
Product Design Solutions
Siemens PLM Software Inc.
Cypress, CA
To an Engineer, the glass is twice as big as it needs to be.
Azonic3d:
Ordinate dims in the sketcher are a mixed blessing, IMHO. I used them in Pro/E for a while, but confusion would often ensue when transferrign the dimensions to the drawing. If you 'showed' the ordinate dims from multiple sketches in a drawing view, there would be multiple '000' dims that had to be aligned. You could end up with dozens of them all overlapping and no good way to ascertain which 000 was associated with which feature.
I eventually abandoned the practice and haven't really missed it.
Ed
Ordinate dims in the sketcher are a mixed blessing, IMHO. I used them in Pro/E for a while, but confusion would often ensue when transferrign the dimensions to the drawing. If you 'showed' the ordinate dims from multiple sketches in a drawing view, there would be multiple '000' dims that had to be aligned. You could end up with dozens of them all overlapping and no good way to ascertain which 000 was associated with which feature.
I eventually abandoned the practice and haven't really missed it.
Ed
There's also nothing stopping you from defining hole centres with several separate sketches and rectangle select the points to make a single hole. Have a look at the attached.
Best Regards
Hudson
www.jamb.com.au
Nil Desperandum illegitimi non carborundum
Best Regards
Hudson
www.jamb.com.au
Nil Desperandum illegitimi non carborundum
- Thread starter
- #8
@acciardi
I see your point. I've run into similar types of issues in other CAD programs; drawing functionality doesn't always translate well from the model/dimension/annotation features. Just seems that was the whole point of 3D, to avoid having to do things twice to create the drawing. I'm still hoping for the day when our suppliers use the ASME Y14.41 standard...
@hudson888
Actually, this particular piece did have 4 different hole location sketches, but mainly because each hole was different in size. It just happens that the screenshot I showed is the one with a LOT of hole locations
Thanks for all the help. I'm really loving what a great resource this forum has been.
I see your point. I've run into similar types of issues in other CAD programs; drawing functionality doesn't always translate well from the model/dimension/annotation features. Just seems that was the whole point of 3D, to avoid having to do things twice to create the drawing. I'm still hoping for the day when our suppliers use the ASME Y14.41 standard...
@hudson888
Actually, this particular piece did have 4 different hole location sketches, but mainly because each hole was different in size. It just happens that the screenshot I showed is the one with a LOT of hole locations
Thanks for all the help. I'm really loving what a great resource this forum has been.
- Status