Recent content by zhanshenjing

ｗｈｉｌｅ　Ｉ　ｔｒｉｅｄ　ｔｏ　ｃｈｅｃｋ　ｔｈｅ　ａｌｌｏｗ　ｓｅｐａｒａｔｉｏｎ　ｂｏｘ,　ｓｏｒｒｙ　ｆｏｒ　ｔｈａｔ　Ｉ　ｄｉｄｎ'ｔ　ｅｘｐｌａｉｎｅｄ　ｉｔ　ｃｌｅａｒｌｙ.　Ｉ　ｊｕｓｔ　ｗａｎｔ　ｎｏ　ｐｅｎｅｔｒａｔｉｏｎ,　ｎｏｔ　ｔｉｅ　ｔｈｅｍ　ｔｏｇｅｔｈｅｒ

I modeled two piece of ｓｈｅｌｌ　ｗｉｔｈ　ｓｕｒｆａｃｅ　ｔｏ　ｓｕｒｆａｃｅ　ｃｏｎｔａｃｔ,　Ｉ　ｊｕｓｔ　ｗａｎｔ　ｔｈｅｍ　ｎｏｔ　ｔｏ　ｐｅｎｅｒｔｒａｔｅ　ｅａｃｈ　ｏｔｈｅｒ,　ｈｏｗｅｖｅｒ,　ｔｈｅ　ｅｆｆｅｔ　ｏｆ　ｔｈｅ　ｃｏｎｔａｃｔ　ｂｅｈｅａｖｅｓ　ｌｉｋｅ　ｔｉｅ　ｔｈｅｍ　ｔｏｇｅｔｈｅｒ,　ｃａｎ　ａｎｙｏｎｅ　ｈｅｌｐ　ｅｘｐｌａｉｎ　ｔｈｉｓ?

Hi，corus is there anyway to display cpress based on element？ It seems that abaqus only allow banded display mode.

Hi, everyone. I recently used general contact to define the surface contact between two shell component. But the result show both positive and negative cpress value. I checked the allow separation, what else that might be wrong can lead to this result? Thanks

Hi everyone, I have two solid parts in hypermesh, they have a common face, but this common face is only part of each surface, is it possible to only merge part of surface, not whole surface?

I am modeling a spot weld, but has some difficulty in connecting two parts (beam and shell) together, is there any good advice?

Manual doesn't say the steps of this， anyone have the experience ？ In which step to do this？ mesh or defining connector section？

I want to assign elastic-plastic material behavior to the bushing, but stuck at the elasticy . It has linear, nonlinear and rigid choice, rigid is simple but how to give a elastic modulus of 200Gp to it, the interface is hard to understand. Someone know this?

Thank you all for replying. I used tie and embeded constrain， both of them produce seriously stress concentration and result none continual stress in the contact area. Rigid connection is not what I want. Finally I used shell to solid coupling that produced nicer results. So Denial, it is proved...

thank you rb1957 I am doing this welding in abaqus, I will try to read the manual about the coincident node as you advised.

Hi， Rb1957 I want to connect a shell surface to a cylinder. I have tried to use shell to solid even though it give good results but I want to use another way to prove it is right.

Hi，Prebasha I have a question about （1） ：in abaqus is it possible to merge nodes on two parts another question about （2） ： If shell and solid have different thickness， can I do this？

how to connect a solid to a shell surface? not to the edge?

I am trying to connect a solid cylinder to a shell plate， anyone have some idea how to connect them in Abaqus? Any idea is appreciated. bending moment will be transmitted..

another linkhttp://files.engineering.com/getfile.aspx?folder=ff74fb1b-f3ff-4c17-9184-4702e9cc8e70&file=JA@))7A`QV]86A0~%F8LVKS.jpg