Search results for query: *

We finally received specific torque values from the OEM...235-265 in-lb torque.

It is not a military C130 but rather a civilian L100-30. We have resolved this particular issue but getting a copy of TO 1-1A-8 would be nice... :) Phil

The hard copy of SAE AS 870 is available ($72.68) from IHS but I don't really have time to order it. The cost is not so much the issue... Phil

FYI I realize that torque specs are part of the joint design but I guess I'm wondering if there is any relevant reference that may help. A stab in the dark I know...! BTW if there are any c130 folks out there, this relates to the Main Landing Gear Beam to Drag Angle connection (STA577...

I have a combination of the following bolt & nut (also some washers): Bolt MS21250-05016 Nut H55LH4367-054 I have no direction in the SRM regarding the torque. While I have requested confirmation from the aircraft manufacturer, in the mean time I am trying to chase down something that can be...

I managed it using a macro from here... http://solidmentor.com/modules/wiwimod/index.php?page=NewPointCloudMacro Then in the resulting 3D sketch, insert a continuous line around the perimeter. Then using the Surface Fill feature, and scaling 25:1 on the Z-axis. you can really see the crown...

I have never used macros in SW before. How would I apply this to my file? Phil

I am running SW Office 2007 SP0.0. I have a spreadsheet containing elevation data from an airport runway. The data is from a survey which took elevation measurements on a 3 meter grid. This particular runway has some serious dips in it that I would like to show graphically. I had hoped to...

Are there any FAA DER's delegated to sign off aerodynamic? We have an FAA structures DER working on a B737 Upper wing surface repair, and need an aerodynamic signoff. Any suggestions? PhilLee

Also got a copy of the applicable section from Rev D from another source. Phil

RPstress, rec'd fax... thanks, Phil

Wil Taylor, I have confirmed that a paper copy of Rev D is available from IHS ($247). RPstress, If you could fax the pages to 613-254-6339 that would be greatly appreciated. Phil

There was an old thread on this subject (thread2-127095)... I need the material properties, allowables for Aluminum Alloy 7178-T6511. Does anyone have them? As mentioned in the old thread, apparently MIL-HDBK-5 rev D had them but I cannot get my hands on it. I have Rev J, as well as...

How about a B737 and ATR42? thanks, Phil

ok I'm back... Using the Curve Driven Brush as a reference I have succesfully made the helix, 3D sketch, and then used the Curve Driven Pattern Feature to get 5 holes to follow the helical spline in the 3D sketch at a 0.5" spacing. The propblem now is that the holes (cuts) are not rotating as...

The Curve driven brush looks like what I need...I go through that and figure it out. might be back later! Phil

I tried the Pattern Feature tutorial and I agree that this is perhaps on the right track. I did the tutorial and providing I can find a way to 'Skip Instances' such that I am left with cuts at the following locations only (1,1) (2,2) (3,3) (4,4). Using the Linear pattern then followed by the...

I was waiting for this question! :) The smaller pipe has a pattern of holes (5 holes offset 30 degrees radially and 1/8" lengthwise from each other) I agree that I could do each individually (insert a plane tangent to the face and 'cut') but when I discovered the 'wrap' command I thought it...

I have sketched a pattern of holes on a plane and then used the Wrap feature to 'wrap' them around a pipe. I then 'Debossed' them to make holes through the wall of the pipe. This is a smaller pipe that slides into a larger pipe. The larger pipe has single hole in it. This hole is sketched on...

ok I added the following parts with the wizard... AN3 through AN20 bolts (complete with configuration table with all available diameters, lengths, etc...) AN960 washer (also with configuration table) MS20365 self locking nut They are all visable under Tools, Options, System Options, Data...