Search results for query: *

Any one familar with gasket material selection out there? I am specifing the material of a water box gasket with max. pressure 150 psi and max temp. 130 F. Looking for advise on the following properties: hardness per ASTM2240, Compression set 25% compressor per D395, creep relaxation. Thanks...

Thanks for the valuable input. More questions... Per UL, when the control panel of equipment is designed, do we need to size the wire according to Wiring Ampacity Table AND temperature test the wire, or do just one of the two requirments? Thanks,

Hi, folks, I have a question regarding wire sizing per NEC. UL requires hazardous voltage circuit conductors supplying one motor shall have an ampacity not less than 125% of the motor full load current rating. Does NEC have the same requirement? I found ampacity table 310-16 &17 in NEC 2005...

Is there a sight glass you can use to check the oil level? Throttling the water valve on the cooling water loop, you will be able to raise the condening pressure and let the chiller run warmer. Good luck!

Hi, I used R23, which is the replacement of R13 in a cascade system before. Why do you still want to use R13? I wanted to tried Suva 95,but could not get the system component. However, the ability of the compressor to handle the refrigerant is related to the pressure. If you could design a...

Hi, the screw compressor relies on minimum gas velocity to take the oil in the evaporator back to the compressor. If the compressor is running unloaded for extended period of time. The oil will accumulate in the evaporator. There will be not enough oil back to the compressor. wzal

Hi, I am designing the defrosting system for a box @ -18 C. I installed one solenoid valve on liquid line and another one on hot gas line. Do I need to put one valve (check valve or solenoid valve) on discharge line between compressor and condenser inlet? I checked a few books and found it was...

Hi, Where could I find a pressure relieve valve with setting 15-25 psi (for air)? Thanks,

Hi, I am designing a freezer with eletric defrost heater. Cooling capacity 1,000 btu/h at 5 F box temperature. How much is the power I should put in the heater? I know it depends on a lot of factors such as moisture of the load, defrosting cycle etc. But I need something to start with and do...

Hi, I am looking for a pressure regulating valve that will keep the downstream pressure at 10-15 psi. Anybody knows where I could find it? Only small amount of nitrogen will go through the valve. Upstream pressure 100-300 psi. Thanks,

Hi, I am looking for a pressure regulating valve that will keep the downstream pressure at 10-15 psi. Anybody knows where I could find it? Only small amount of nitrogen will go through the valve. Upstream pressure 100-300 psi. Thanks,

Hi, we are planning to convert the refrigerant of a cascade system from R23 to R508B (Suva 95). Is it necessary to change the expansion valve? Thanks,

Does anyone know whether I can use Castrol Icematic SW32 for my Bitzer 4H-25.2 (recip compressor) and R23 (HFC for cryogenic application)? Unfortunately, it is an old installation and I lost contact with the compressor manufacturer. Thanks if anyone could provide some input.

Thank you all for your valuable input. I have a Lovejoy Jaw type and a Rex Omega coupling. Both of them have torque capacity 4 times of continuous torque of the application. But both of the 2 coupling manufacturers didn't say how much is the service factor I should use on the spec. (it seems to...

Hi, I am designing a direct drive system including an electric motor and a 6 -cylinder reciprocating compressor. How much is the service factor I should use when I size the key and coupling hub/spider (because of the vibration)? Thanks,

Hi, I am new to the commercial and industrial heating business in North America and have some questions. Is boiler using coal very popular in North America? Or is oil or natural more popular? I am reading a book about stationary engineer and the book says stationary engineers have to look at...

What we are developing is an A/C for truck driver. Regards,

Thank you for your input, imok2. I don't have the performance data of the scroll and pistion compressor I am comparing. They are a little special (open drive and small displacement for automotive). That's why I ask the general question. I am sure scroll compressor will have much higher...

HI, Everyone, I am working on an mobile air conditioning system and needs an R134a compressor that has best efficiency when pressure ratio is 2:1. Is a scroll compressor more efficient than piston at the pressure ratio? Thanks,

Hi, Everyone, We are developing a small AC system for vehicle and need compressor about 40cc using 134a. I searched web and found most of the compressor are 80cc and up. Is there anybody who knows the compressors I am looking for? Thanks,