Search results for query: *

Potosí, Bolivia. The information that I have been able to gather up to now is the following: Apparently they used the bolts as supports to assemble the last tank ring. The shoring was done with tubular wire E71T-1. If I have more information, I will inform you as soon as possible. Thank you!

Dear, Good morning; I would like to know the tolerance in millimeters between the separation of the bottom of the tank with the cemented base and of being outside the tolerance which is the correct correction process. Example.- Template of the tab through the use of 20 lb. rope. The tank is...

Dear; Good morning, I have detected that the anchor bolts in a storage tank (API 650), are propped up (see image) the supervisor in charge has indicated to me that this has been done by constructive process. Well I assume it is the first time that this contractor makes this type of assembly...

Dear; Good afternoon, I am assembling a storage ship and in the approved plans for construction I have the following connection detail in the union beam-beam: The board is bolted but my client tells me that we solder that board, I have consulted my technical office but they still do not...

1.- The column was not designed correctly. 2.- The supporting load is "small". In conclusion after straightening I will reinforce it.

The appearance of the structure is due to the deposition of paint and over time have formed "protective layers" that appear to have rid the steel of the oxidation. The entire structure works as a "paint booth".

Dear ; Good afternoon, A client has asked me to reinforce 4 ships, I am doing the relevant reviews and I have found the following surprise: The beam that works as a column has been deformed. According to what my client indicates is because they had problems when mounting the roof and...

What is the difference between ANSI 818.2.2 and ASME B18.2.2

Thank you very much for your answer.

Dear; Good morning, I wonder if I replace a millimetric nut "ASTM A563M" class 10S by millimeter nut "ASTM A194M 2H". In case you can not make the change that equivalent could replace it? Consider the bolt is Millimeter "ASTM A325M-1" and be supplied galvanized. Thank you very much for...

Dear; Good morning, I wonder if I replace a millimetric nut "ASTM A563M" class 10S by millimeter nut "ASTM A194M 2H". In case you can not make the change that equivalent could replace it? Consider the bolt is Millimeter "ASTM A325M-1" and be supplied galvanized. Thank you very much for...

It is 83 ° to be exact.

Dear; Good Morning, Someone who can tell me the American standard for countersunk bolts? Best regards.

Dear; Good afternoon, There is a difference between VICTAULIC accessories brand with other brands?. Since eh observed that the Victaulic brand, have a higher cost. Best regards.

Dear; Good morning, I was reviewing the plans for my client and found that there eh grooved boards where not specify what type of coupling victaulic must carry. I would like to know what conditions must meet the line to install flexible or rigid coupling victaulic. Greetings.

Dear; I require support for interpreting the following: - GROOVED ENDS 6MM RUBBER LINED For example: - PIPE ERW SCH 40 CS A53-B GROOVED ENDS 6MM RUBBER LINED Thanks for your support

Dear; Good morning, I have received galvanized pipe work with dirt on the outside of the tube I wonder if they know of any solution to clean the tubes because dirt is relatively low. PS: Mainly spots are indelible marker, earth.

Sorry, the line is 2 ".

Dear ; Good afternoon, I will make a line of stainless / Monel 400 pipe, I wonder what suggestions may indicate me to bring good manufacturing process, welding and cleaning. The line is 3 "and the seals are SW. The manufacture is for a hydrogen plant. Best regards.

The thickness of the fixture is to be reduced by 9 mm, it is too in my opinion not risk the line to place said accessory designer see if you can make a graft tube 14 ". Otherwise quoted by a tee in sch-160 which is more commercial.