Search results for query: *

Try the attachment at the link below instead of the one above.https://plus.google.com/photos/100708884121076343479/albums/5924366093008198913?authkey=CO6cofX-jfSjuAE

Hello! I am currently designing an electrical continuity tester for a flex circuit. The circuit itself is a series of copper bars that are mechanically connected to traces through different buses. My idea is very basic: connect a trace to the test circuit (a power supply plus some sort of...

Hi all, To start off, I should say that I am a rookie when it comes to laser cutting. I am trying to cut circular cross section holes in pharmaceutical capsules that are composed of gelatin or vegetable based materials. These holes would range in .032" to .05". Is this doable from a material...

Hi all, I'm not sure if this is the right forum, so please advise if this should be moved elsewhere - I couldn't find a packaging engineering forum. I work at a biomedical device company, and have a need for implementing an error or mistake proofing system with respect to product labeling...

Can you provide a link? Where would I find and read up about this?

I am having some artwork pad printed on a part, but am concerned with the durability of the pad print over time. The part is a component of a consumer product, and will go in pockets, briefcases, etc. I fear that it will noticeably wear over time due to these types of environments. Although the...

My first thought is to use a film layer, please let me know if you have any suggestions on this.

I am having some artwork pad printed on a part, but am concerned with the durability of the pad print over time. The part is a component of a consumer product, and will go in pockets, briefcases, etc. I fear that it will noticeably wear over time due to these types of environments. Although...

I guess I did not properly qualify the statement made for my question concerning 'Option (1)'. I am looking for hinge suppliers, not case suppliers.

I am currently designing a small (approx 4.5"W x 3.5"L x 1"T) plastic case. Everything is sorted out but the hinge, as I do not have experience with hinge design. That being said, I see two options: (1) source a hinge from a supplier - that way I avoid the design portion, or (2) learn how to...

Unfortunately I am not - I'm in San Luis Obispo, California. Thank you for the strength tip

Hi all, I am looking for pre-terminated/fitted wire rope. The wire rope should be 1/8" diameter w/ some type of plastic coating (doesn't matter what plastic formulation is used), and the terminations should be ball ends. I ask for pre-terminated because from my initial research, it looks...

Hi all, I am seeking an inexpensive photoelectric displacement sensor. The requirements of the sensor are that it senses over a 10mm range (preferably 0-10mm, but could be greater like 30-40mm), and is accurate to .1mm. The application is to detect the distance of a rubber tube that will...

Hi all, I have a question concerning costs for different manufacturing processes. I'm a rather fresh ME, so please bear with me. I am concerned with the cost of manufacturing the bracket depicted in the attached image. I am looking for the lowest cost option to manufacture the bracket from...

Hi all, I am in search of a supplier for a low cost ratchet mechanism containing a ratchet wheel/gear and pawl. It is for a light load application, and can be manufactured from any metal, but I imagine getting my hands on a cheap steel or brass one would be easiest. The ratchet solution would...

The pump is an air powered pneumatic pump. It operates all day, at a maximum flow rate of .1 gpm. Here is a link to the pump: http://www.mcmaster.com/#6770K41 What are the metal devices you referred to?

My question is: what fluid dispensing container would you recommend for this low flow pump application?

I neglected to mention that this is for a low flow rate situation. A reservoir volume of 1 gallon is sufficient - just to give you a ballpark idea.

I have a simple fluid dispensing question. My situation requires feeding a pump with isopropyl alcohol. I would like to place whatever container dispenses the fluid above the suction side of the pump. The pump is currently equipped with a 3/8 inch ID tube at the suction side. The dispenser...

(1) The number of tubes can range, anywhere from 1 to 10 (2) No size constraints on the size of the adapter (I'm assuming you were referring to the gripper/adapter itself) (3) The tube material is stainless 304 (4) Long term setup