SOL 101 and 103 run perfectly, but SOL 105 gives excessive pivot ratios

[jomocas]

Hello all,

So I am trying to do a Buckling analysis to a condensed Model and I get the Fatal Message 9050 (SEKRRS):

GRID POINT ID DEGREE OF FREEDOM MATRIX/FACTOR DIAGONAL RATIO MATRIX DIAGONAL

57004426 T1 -8.79996E+08 2.05308E+09
57004426 T2 2.05269E+08 8.17563E+08
57004426 T3 5.24272E+07 5.46972E+08
^^^
^^^ USER FATAL MESSAGE 9050 (SEKRRS)
^^^ RUN TERMINATED DUE TO EXCESSIVE PIVOT RATIOS IN MATRIX KLL.
^^^ USER ACTION: CONSTRAIN MECHANISMS WITH SPCI OR SUPORTI ENTRIES OR SPECIFY PARAM,BAILOUT,-1 TO
CONTINUE THE RUN WITH MECHANISMS.

So I get a negative Matrix/Factor Diagonal Ratio and this won't allow Nastran to continue. Does anybody know why I get a negative Matrix/Factor Diagonal Ratio for SOL 105 but not for SOL 101? The model is exactly the same and I looked at this node and it looks absolutely normal. All the model are 3D CHEXA elements by the way.

Thanks a lot,

 

[hezhj2000]

What are the natural frequencies you got from Sol 103 run? One possibility is that in your your Sol 101 run, your applied force direction is constrained, while other directions are not constrained.

 

[jomocas]

Hi hezhj200,

Thanks for your reply.

So the first 2 frequencies are around 11Hz, the 3rd is 89 Hz and the tenth is around 190 Hz.

I don't understand your possibility, could you re explain it? I have exactly the same loads on both calculations. In the SOL 101 I have SC1 with the SOL 105 Preload and SC2 with the SOL 105 Buckling laod.

Thanks,

 

[hezhj2000]

Forget about my possibility. The Sol 103 results show that there are no rigid body modes. So my possibility will not hold.

Is it possible that you use different constraints for the 2 subcases in Sol 105?

 

[jomocas]

No, the constraints are exactly the same. Only one Subcase has temperature and the other one doesnt.

I upload both Input Decks, maybe it helps...

SOL 101

SOL 101
CEND
ECHO = NONE
$$------------------------------------------------------------------------------$
$$       Case Control Cards        $
$$------------------------------------------------------------------------------$
$
K2GG=KAAX,KAAGGX
P2G=PAX
$
$ ******************* Subcase ***********************************
SUBCASE 1
SUBTITLE=LC1 -  - GROUND  - Reverse Pressure - Preload
LOAD=101
TEMP=9999
SPC=500
DISP(PLOT)=ALL
STRESS(PLOT)=ALL
$
SUBCASE 2
SUBTITLE=LC1 -  - GROUND  - Reverse Pressure - LifeLoad
LOAD=102
SPC=500
DISP(PLOT)=ALL
STRESS(PLOT)=ALL
$
SUBCASE 3
SUBTITLE=LC2 -  - GROUND  - Filling(ATAT) - Preload
LOAD=201
TEMP=4103
SPC=500
DISP(PLOT)=ALL
STRESS(PLOT)=ALL
$
SUBCASE 4
SUBTITLE=LC2 -  - GROUND  - Filling(ATAT) - LifeLoad
LOAD=202
SPC=500
DISP(PLOT)=ALL
STRESS(PLOT)=ALL
$
$
$ ***************************************************************
$
$
BEGIN BULK
$
$
$ ****************** Loads **************************************
LOAD    101     1.0     2375000.57110   2375000.57111   35000.  57200
        35000.  57201   0.0     57500   0.0     57501	1271250.57180
        1271250.57181   1006000.57112   1006000.57113
$
$
LOAD    102     1.0     1051000.57192   1051000.57193                                           
$
$
LOAD    201     1.0     23313.0 58710   427.35  58401   852.511 58301
        2919.71 58307   1875.56 58303   0.0     58304   261.188 58305
        2375000.57110   2375000.57111   35000.  57200   35000.  57201
        0.0     57500   0.0     57501   1250000.57180   1250000.57181
        1006000.57112   1006000.57113   0.0     57230   0.0     57231
        0.0     57530   0.0     57531   
$
$
LOAD    202     1.0     1051000.57192   1051000.57193
$ ***************************************************************
$
$
PARAM,AUTOSPC,YES
PARAM,CHECKEL,NO 
PARAM,PRGPST,NO
PARAM,POST,0
$
$
$-------$-------$-------
TEMPD   4103    293.0   
TEMPD   3050    293.0 
TEMPD	9999	300.0
$
$-------$-------$-------$-------$-------
SPCADD  500     501
SPC     501     201856  123456  0.0 
$
$ ********* Boundary Condition - FULLY FIXED AT I/F BME-RIE **********
$
RBE2     201856  201856  123456  201500  201505  201510  201515  201520
         201525  201530  201535  201540  201545  201550  201555  201560
         201565  201570  201575  201580  201585  201590  201595  201600
         201605  201610  201615  201620  201625  201630  201635  201640
         201645  201650  201655  201660  201665  201670  201675  201680
         201685  201690  201695  201700  201705  201710  201715  201720
         201725  201730  201735  201740  201745  201750  201755  201760
         201765  201770  201775  201780  201785  201790  201795  201800
         201805  201810  201815  201820  201825  201830  201835  201840
         201845  201850  201855
GRID     201856  201     0.      0.     3.74
$
$
$
$ ********* DMIG  ******************************************************
$
INCLUDE'CONDENSED_PARTS_gto_sl.pch'
INCLUDE'Ground_PAX_v2.bdf'
INCLUDE'Ground_KAAX_v2.bdf'
$  
$ ********* Model ******************************************************
$
INCLUDE 'ASET-Nodes_SL_def.bdf'
INCLUDE 'Ground_LC1-LC2_MODEL.bdf'
$
$ ********* Loads ******************************************************
$
INCLUDE 'Ground_LC1-LC2_LOADS.bdf'
INCLUDE'Ground_LLC1-LC2_TEMPS.bdf'

$
$
ENDDATA

SOL 105

SOL 105
CEND
ECHO = NONE
$$------------------------------------------------------------------------------$
$$       Case Control Cards        $
$$------------------------------------------------------------------------------$
$
K2GG=KAAX,KAAGGX
P2G=PAX
$
$ ******************* Subcase ***********************************
SUBCASE 1
SUBTITLE=LC1 - GROUND - Reverse Pressure - Preload
LOAD=101
TEMP=9999
SPC=500
DISP(PLOT)=ALL
STRESS(PLOT)=ALL
$
SUBCASE 2
SUBTITLE=LC1 - GROUND  - Reverse Pressure - LifeLoad
LOAD=102
SPC=500
DISP(PLOT)=ALL
STRESS(PLOT)=ALL
$
SUBCASE 3
SUBTITLE=LC2 - GROUND  - Filling(ATAT) - Preload
LOAD=201
TEMP=4103
SPC=500
DISP(PLOT)=ALL
STRESS(PLOT)=ALL
$
SUBCASE 4
SUBTITLE=LC2 - GROUND  - Filling(ATAT) - LifeLoad
LOAD=202
SPC=500
DISP(PLOT)=ALL
STRESS(PLOT)=ALL
$
$
SUBCASE 10
SUBTITLE=LC1 - GROUND  - Reverse Pressure - Buckling
STATSUB(PRELOAD)=1
STATSUB(BUCKLING)=2
VECTOR(PLOT)=ALL
METHOD=1
$
SUBCASE 11
SUBTITLE=LC2 - GROUND  - Filling(ATAT) - Buckling
STATSUB(PRELOAD)=3
STATSUB(BUCKLING)=4
VECTOR(PLOT)=ALL
METHOD=2
$
$
$ ***************************************************************
$
$
BEGIN BULK
$
$
$ ****************** Loads **************************************
$
$
LOAD    101     1.0     2375000.57110   2375000.57111   35000.  57200
        35000.  57201   0.0     57500   0.0     57501	1271250.57180
        1271250.57181   1006000.57112   1006000.57113
$
$
LOAD    102     1.0     1051000.57192   1051000.57193                                           
$
$
LOAD    201     1.0     23313.0 58710   427.35  58401   852.511 58301
        2919.71 58307   1875.56 58303   0.0     58304   261.188 58305
        2375000.57110   2375000.57111   35000.  57200   35000.  57201
        0.0     57500   0.0     57501   1250000.57180   1250000.57181
        1006000.57112   1006000.57113   0.0     57230   0.0     57231
        0.0     57530   0.0     57531   
$
$
LOAD    202     1.0     1051000.57192   1051000.57193
$
$
$ ***************************************************************
$
$
PARAM,AUTOSPC,YES
PARAM,CHECKEL,NO 
PARAM,PRGPST,NO
PARAM,POST,0
$
$
$
$
EIGRL   1       0.              30
EIGRL   2       0.              30
$
$
$-------$-------$-------
TEMPD   4103    293.0   
TEMPD   3050    293.0 
TEMPD	9999	300.0
$
$-------$-------$-------$-------$-------
SPCADD  500     501
SPC     501     201856  123456  0.0 
$
$ ********* Boundary Condition - FULLY FIXED AT I/F BME-RIE **********
$
RBE2     201856  201856  123456  201500  201505  201510  201515  201520
         201525  201530  201535  201540  201545  201550  201555  201560
         201565  201570  201575  201580  201585  201590  201595  201600
         201605  201610  201615  201620  201625  201630  201635  201640
         201645  201650  201655  201660  201665  201670  201675  201680
         201685  201690  201695  201700  201705  201710  201715  201720
         201725  201730  201735  201740  201745  201750  201755  201760
         201765  201770  201775  201780  201785  201790  201795  201800
         201805  201810  201815  201820  201825  201830  201835  201840
         201845  201850  201855
GRID     201856  201     0.      0.     3.74
$
$
$
$ ********* DMIG  ******************************************************
$
INCLUDE'CONDENSED_PARTS_gto_sl.pch'
INCLUDE'Ground_PAX_v2.bdf'
INCLUDE'Ground_KAAX_v2.bdf'
$  
$ ********* Model ******************************************************
$
INCLUDE 'ASET-Nodes_SL_def.bdf'
INCLUDE 'Ground_LC1-LC2_MODEL.bdf'
$
$ ********* Loads ******************************************************
$
INCLUDE 'Ground_LC1-LC2_LOADS.bdf'
INCLUDE'Ground_LLC1-LC2_TEMPS.bdf'

$
$
ENDDATA

 

[nlgyro]

I'm a bit surprised that you are using DMIG's in a sol105, unless you're sure that the buckling modes are defined by the residual structure.

Can you post the relevant sections of the sol105 f06 file?

 

[jomocas]

Hi nlgyro,

The DMIGs are a requirement of the customer...

Why do you mean by the relevant sections? What exactly do you want me to post?

Thanks in advance,

Jose

 

[nlgyro]

Can you post the portion of the f06 upto the point when the job fatal's out?

 

[jomocas]

This is the f06 upto the fatal point:

1                                                                              JUNE  24, 2014  MSC.NASTRAN 12/21/10   PAGE     1           
                                                                                                                                           
0        N A S T R A N    F I L E    A N D    S Y S T E M    P A R A M E T E R    E C H O                                                  
0                                                                                                                                          
                                                                                                                                           
                                                                                                                                           
     NASTRAN BUFFSIZE=35000 $(C:/MSC.SOFTWARE/MSC_NASTRAN/20101/CONF/NAST20101.RCF[2]                                                      
     NASTRAN DBCFACT=4 $(C:/MSC.SOFTWARE/MSC_NASTRAN/20101/CONF/NAST20101.RCF[9])                                                          
     NASTRAN PARALLEL=4 $(COMMAND LINE[2])                                                                                                 
     NASTRAN REAL=2144075776 $(PROGRAM DEFAULT)                                                                                            
     NASTRAN BUFFSIZE=35073 $(C:/MSC.SOFTWARE/MSC_NASTRAN/20101/CONF/NAST20101.RCF[2]                                                      
1                                                                              JUNE  24, 2014  MSC.NASTRAN 12/21/10   PAGE     2           
                                                                                                                                           
0        N A S T R A N    E X E C U T I V E    C O N T R O L    E C H O                                                                    
0                                                                                                                                          
                                                                                                                                           
                                                                                                                                           
     SOL 105                                                                                                                               
     CEND                                                                                                                                  
1                                                                              JUNE  24, 2014  MSC.NASTRAN 12/21/10   PAGE     3           
                                                                                                                                           
0                                                                                                                                          
0                                        C A S E    C O N T R O L    E C H O                                                               
                 COMMAND                                                                                                                   
                 COUNT                                                                                                                     
                  1      ECHO = NONE                                                                                                       
                  2      $$----------------------------------------------------------------------        --------                          
                  3      $$       CASE CONTROL CARDS        $                                                                              
                  4      $$----------------------------------------------------------------------        --------                          
                  5      $                                                                                                                 
                  6      K2GG=KAAX,KAAGGX                                                                                                  
                  7      P2G=PAX                                                                                                           
                  8      $                                                                                                                 
                  9      $ ******************* SUBCASE ***********************************                                                 
                 10      SUBCASE 1                                                                                                         
                 11      SUBTITLE=LC1 - GROUND - REVERSE PRESSURE - PRELOAD                                           
                 12      LOAD=101                                                                                                          
                 13      TEMP=9999                                                                                                         
                 14      SPC=500                                                                                                           
                 15      DISP(PLOT)=ALL                                                                                                    
                 16      STRESS(PLOT)=ALL                                                                                                  
                 17      $                                                                                                                 
                 18      SUBCASE 2                                                                                                         
                 19      SUBTITLE=LC1 - GROUND - REVERSE PRESSURE - LIFELOAD                                          
                 20      LOAD=102                                                                                                          
                 21      SPC=500                                                                                                           
                 22      DISP(PLOT)=ALL                                                                                                    
                 23      STRESS(PLOT)=ALL                                                                                                  
                 24      $                                                                                                                 
                 25      SUBCASE 3                                                                                                         
                 26      SUBTITLE=LC2 - GROUND - FILLING(ATAT) - PRELOAD                                              
                 27      LOAD=201                                                                                                          
                 28      TEMP=4103                                                                                                         
                 29      SPC=500                                                                                                           
                 30      DISP(PLOT)=ALL                                                                                                    
                 31      STRESS(PLOT)=ALL                                                                                                  
                 32      $                                                                                                                 
                 33      SUBCASE 4                                                                                                         
                 34      SUBTITLE=LC2 - GROUND - FILLING(ATAT) - LIFELOAD                                             
                 35      LOAD=202                                                                                                          
                 36      SPC=500                                                                                                           
                 37      DISP(PLOT)=ALL                                                                                                    
                 38      STRESS(PLOT)=ALL                                                                                                  
                 39      $                                                                                                                 
                 40      $                                                                                                                 
                 41      SUBCASE 10                                                                                                        
                 42      SUBTITLE=LC1 - GROUND - REVERSE PRESSURE - BUCKLING                                          
                 43      STATSUB(PRELOAD)=1                                                                                                
                 44      STATSUB(BUCKLING)=2                                                                                               
                 45      VECTOR(PLOT)=ALL                                                                                                  
                 46      METHOD=1                                                                                                          
                 47      $                                                                                                                 
                 48      SUBCASE 11                                                                                                        
                 49      SUBTITLE=LC2 - GROUND - FILLING(ATAT) - BUCKLING                                             
                 50      STATSUB(PRELOAD)=3                                                                                                
1                                                                              JUNE  24, 2014  MSC.NASTRAN 12/21/10   PAGE     4           
                                                                                                                                           
0                                                                                                                                          
0                                        C A S E    C O N T R O L    E C H O                                                               
                 COMMAND                                                                                                                   
                 COUNT                                                                                                                     
                 51      STATSUB(BUCKLING)=4                                                                                               
                 52      VECTOR(PLOT)=ALL                                                                                                  
                 53      METHOD=2                                                                                                          
                 54      $                                                                                                                 
                 55      $                                                                                                                 
                 56      $ ***************************************************************                                                 
                 57      $                                                                                                                 
                 58      $                                                                                                                 
                 59      BEGIN BULK                                                                                                        
 *** USER WARNING MESSAGE 324 (XSORSO)                                                                                                     
     BLANK ENTRIES ENCOUNTERED WILL BE IGNORED.                                                                                            
0                             INPUT BULK DATA ENTRY COUNT =********                                                                        
0                       TOTAL COUNT= 202775961                                                                                             
1                                                                              JUNE  24, 2014  MSC.NASTRAN 12/21/10   PAGE     5           
                                                                                                                                           
0                                                                                                                                          
0                                D U P L I C A T E   B U L K D A T A   D E L E T I O N   S U M M A R Y                                     
                                                                                                                                           
                                                                                                                                           
 DPBLKTOL (SYSTEM 402) = 0.0  (DEFAULT)                                                                                                    
                                                                                                                                           
 ALL FIELDS OF DELETED BULKDATA ENTRIES MUST BE EXACTLY IDENTICAL.                                                                         
 FIELDS ARE CONSIDERED EXACTLY IDENTICAL IF THE CORRESPONDING CHARACTERS ARE THE SAME.                                                     
                                                                                                                                           
 ONE OR MORE GRID ENTRIES WITH THE FOLLOWING ID(S) HAVE BEEN REMOVED AS A DUPLICATE:                                                       
                826000  826010  826017  826025  826032  826040  826050  826060  826070  826080  826090                                     
                826100  826107  826115  826122  826130  826140  826150  826160  826170  826180  826190                                     
                826197  826205  826212  826220  826230  826240  826250  826260  826270  826280  826287                                     
                826295  826302  826310  826320  826330  826340  826350                                                                     
                                                                                                                                           
                                                                                                                                           
                                             E N T R Y   D E L E T I O N   C O U N T                                                       
                                                                                                                                           
          ENTRY                 ENTRIES              ENTRIES                                                                               
          NAME                    FOUND              DELETED                                                                               
          ----------         ----------           ----------                                                                               
          CORD2C                      5                    0                                                                               
          CORD2R                      5                    0                                                                               
          CORD2S                      2                    0                                                                               
          GRID                   611937                   40                                                                               
 ^^^                                                                                                                                       
 ^^^ >>> IFP OPERATIONS COMPLETE <<<                                                                                                       
 ^^^                                                                                                                                       
 *** USER WARNING MESSAGE 4124 (IFS3P)                                                                                                     
     THE SPCADD OR MPCADD UNION CONSISTS OF A SINGLE SET.                                                                                  
                                                                                                                                           
                                                                                                                                           
                                        M O D E L   S U M M A R Y                                                                          
                                                                                                                                           
                                   NUMBER OF GRID     POINTS   =   611897                                                                  
                                                                                                                                           
                                   NUMBER OF CBEAM    ELEMENTS =       96                                                                  
                                   NUMBER OF CHEXA    ELEMENTS =   452262                                                                  
                                   NUMBER OF CPENTA   ELEMENTS =      328                                                                  
                                                                                                                                           
                                   NUMBER OF RBE2     ELEMENTS =     2102                                                                  
                                   NUMBER OF RBE3     ELEMENTS =      219                                                                  
1                                                                              JUNE  24, 2014  MSC.NASTRAN 12/21/10   PAGE     6           
                                                                                                                                           
0                                                                                                                                          
0                                                                                                                                          
0                                                                                                                                          
0                                                                                                                                          
                                                                                                                                           
 *** USER INFORMATION MESSAGE 7555 (EHEXGD)                                                                                                
     FINITE ELEMENT GEOMETRY CHECK RESULTS EXCEED TOLERANCE LEVELS FOR THE FOLLOWING ELEMENTS.  METRIC VALUES THAT EXCEED                  
     TEST TOLERANCE LIMITS ARE IDENTIFIED BY ONE OF THE FOLLOWING FLAGS PLACED TO THE RIGHT OF THE METRIC VALUE.                           
        "++++" FOR TEST RESULTS EXCEEDING TOLERANCES.  INFORMATIONAL ONLY.  PROBLEM SOLUTION CONTINUES.  (DEFAULT FLAG)                    
        "IGNR" FOR TEST RESULTS EXCEEDING TOLERANCES.  INFORMATIONAL ONLY.  PROBLEM SOLUTION CONTINUES.                                    
        "WARN" FOR TEST RESULTS EXCEEDING TOLERANCES.  INFORMATIONAL ONLY.  PROBLEM SOLUTION CONTINUES.                                    
        "FAIL" FOR TEST RESULTS EXCEEDING TOLERANCES.  SEVERE ERROR.        PROBLEM SOLUTION TERMINATES.                                   
     USER ACTION: USE THE GEOMCHECK (EXECUTIVE CONTROL STATEMENT) KEYWORD=VALUE TO CHANGE TOLERANCE VALUES IF DESIRED.                     
     A MAXIMUM OF        100 EDGE LENGTH ASPECT RATIO (AR)     TOLERANCE LIMIT VIOLATIONS WILL BE IDENTIFIED BY THE FLAG "++++"            
                             PLACED AFTER THE VALUE METRIC FOR THE TEST.                                                                   
     A MAXIMUM OF        100 EDGE NODE POINT LENGTH RATIO (ER) TOLERANCE LIMIT VIOLATIONS WILL BE IDENTIFIED BY THE FLAG "++++"            
                             PLACED AFTER THE VALUE METRIC FOR THE TEST.                                                                   
     A MAXIMUM OF        100 EDGE NODE POINT ANGLE LIMIT  (EA) TOLERANCE LIMIT VIOLATIONS WILL BE IDENTIFIED BY THE FLAG "++++"            
                             PLACED AFTER THE VALUE METRIC FOR THE TEST.                                                                   
                         ALL NEG/ZERO DET(JACOBIAN) VALUE (DJ) TOLERANCE LIMIT VIOLATIONS WILL BE IDENTIFIED BY THE FLAG "FAIL"            
                             PLACED AFTER THE VALUE METRIC FOR THE TEST.                                                                   
                             NEGATIVE DET(J) VALUES INDICATE THAT ONE OR MORE DET(J) SIGN CHANGES HAVE OCCURED FOR THE ELEMENT.            
     A MAXIMUM OF        100 WARPED FACE COEFFICIENT           TOLERANCE LIMIT VIOLATIONS WILL BE IDENTIFIED BY THE FLAG "++++"            
                             PLACED AFTER THE VALUE METRIC FOR THE TEST.                                                                   
     USER INFORMATION: THE MAXIMUM MESSAGE COUNT FOR ANY ONE ELEMENT ERROR TEST COULD BE EXCEEDED BY THE                                   
     CUMULATIVE EFFECT OF ALL THE MESSAGES GENERATED FOR ALL OF THE DIFFERENT TESTS PERFORMED.                                             
1                                                                              JUNE  24, 2014  MSC.NASTRAN 12/21/10   PAGE     7           
                                                                                                                                           
0                                                                                                                                          
 TEST THRESHOLD VALUES: HEX_AR =   100.00, HEX_EPLR =   0.50, HEX_EPIA =   150.00, HEX_DETJ =     0.00, HEX_WARP =     0.71                
                       (VISUAL FLAGS ARE DISPLAYED AFTER TEST VALUES THAT EXCEED THE TEST THRESHOLDS AS DISCUSSED ABOVE.)                  
 ELEMENT    ELEMENT   LONGEST    SHORTEST       ASPECT           EDGE POINT      EDGE POINT      MIN. JACOBIAN     FACE WARP               
  TYPE         ID       EDGE        EDGE         RATIO          LENGTH RATIO         ANGLE        DETERMINANT     COEFFICIENT              
  HEXA     57660425     0.02        0.00         24.14       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.68 ++++          
  HEXA     57660433     0.02        0.00         24.12       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.68 ++++          
  HEXA     57660512     0.02        0.00         24.14       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.68 ++++          
  HEXA     57660520     0.02        0.00         24.11       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.68 ++++          
  HEXA     57899416     0.01        0.00          4.98       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.69 ++++          
  HEXA     57899417     0.01        0.00          5.29       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.69 ++++          
  HEXA     57986156     0.01        0.01          1.71       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.69 ++++          
  HEXA     58896125     0.02        0.00          9.29       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.62 ++++          
  HEXA     58896127     0.01        0.00          8.50       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.58 ++++          
  HEXA     58896144     0.01        0.00          3.39       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.53 ++++          
  HEXA     58896152     0.01        0.00          3.60       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.54 ++++          
  HEXA     58896153     0.01        0.00          3.35       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.35 ++++          
  HEXA     58896165     0.01        0.00          3.54       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.45 ++++          
  HEXA     58896167     0.01        0.00          3.60       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.45 ++++          
  HEXA     58896168     0.01        0.00          3.01       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.50 ++++          
  HEXA     58896171     0.01        0.00          4.38       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.35 ++++          
  HEXA     58896178     0.01        0.00          3.34       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.54 ++++          
  HEXA     58896191     0.01        0.00          4.02       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.53 ++++          
  HEXA     58896213     0.01        0.00          3.93       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.67 ++++          
  HEXA     58896225     0.01        0.00          4.97       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.67 ++++          
  HEXA     58896226     0.01        0.00          3.97       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.67 ++++          
  HEXA     58896231     0.02        0.00          4.85       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.43 ++++          
  HEXA     58896234     0.01        0.00          2.54       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.49 ++++          
  HEXA     58896235     0.02        0.00          5.70       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.43 ++++          
  HEXA     58896237     0.02        0.00          9.20       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.61 ++++          
  HEXA     58896239     0.01        0.00          8.42       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.61 ++++          
  HEXA     58896256     0.01        0.00          3.39       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.53 ++++          
  HEXA     58896264     0.01        0.00          3.60       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.53 ++++          
  HEXA     58896265     0.01        0.00          5.39       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.65 ++++          
  HEXA     58896277     0.01        0.00          3.54       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.47 ++++          
  HEXA     58896279     0.01        0.00          3.60       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.47 ++++          
  HEXA     58896280     0.01        0.00          3.01       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.51 ++++          
  HEXA     58896283     0.01        0.00          5.61       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.65 ++++          
  HEXA     58896285     0.02        0.00          4.26       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.54 ++++          
  HEXA     58896287     0.02        0.00          4.24       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.54 ++++          
  HEXA     58896290     0.01        0.00          3.32       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.64 ++++          
  HEXA     58896303     0.01        0.00          4.01       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.53 ++++          
  HEXA     58896325     0.01        0.00          3.93       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.68 ++++          
  HEXA     58896337     0.01        0.00          4.97       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.67 ++++          
  HEXA     58896338     0.01        0.00          3.96       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.68 ++++          
  HEXA     58896343     0.02        0.00          4.76       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.35 ++++          
  HEXA     58896346     0.01        0.00          2.51       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.40 ++++          
1                                                                              JUNE  24, 2014  MSC.NASTRAN 12/21/10   PAGE     8           
                                                                                                                                           
0                                                                                                                                          
 TEST THRESHOLD VALUES: HEX_AR =   100.00, HEX_EPLR =   0.50, HEX_EPIA =   150.00, HEX_DETJ =     0.00, HEX_WARP =     0.71                
                       (VISUAL FLAGS ARE DISPLAYED AFTER TEST VALUES THAT EXCEED THE TEST THRESHOLDS AS DISCUSSED ABOVE.)                  
 ELEMENT    ELEMENT   LONGEST    SHORTEST       ASPECT           EDGE POINT      EDGE POINT      MIN. JACOBIAN     FACE WARP               
  TYPE         ID       EDGE        EDGE         RATIO          LENGTH RATIO         ANGLE        DETERMINANT     COEFFICIENT              
  HEXA     58896347     0.02        0.00          5.60       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.35 ++++          
  HEXA     58896350     0.02        0.00          5.64       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.38 ++++          
  HEXA     58896351     0.01        0.00          2.46       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.46 ++++          
  HEXA     58896354     0.02        0.00          4.80       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.38 ++++          
  HEXA     58896359     0.01        0.00          3.99       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.66 ++++          
  HEXA     58896360     0.01        0.00          4.96       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.65 ++++          
  HEXA     58896372     0.01        0.00          3.97       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.66 ++++          
  HEXA     58896394     0.01        0.00          4.01       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.53 ++++          
  HEXA     58896407     0.01        0.00          3.30       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.61 ++++          
  HEXA     58896410     0.02        0.00          4.25       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.54 ++++          
  HEXA     58896412     0.02        0.00          4.26       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.54 ++++          
  HEXA     58896414     0.01        0.00          5.61       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.65 ++++          
  HEXA     58896417     0.01        0.00          3.01       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.51 ++++          
  HEXA     58896418     0.01        0.00          3.60       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.47 ++++          
  HEXA     58896420     0.01        0.00          3.54       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.47 ++++          
  HEXA     58896432     0.01        0.00          5.38       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.65 ++++          
  HEXA     58896433     0.01        0.00          3.61       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.52 ++++          
  HEXA     58896441     0.01        0.00          3.38       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.52 ++++          
  HEXA     58896458     0.01        0.00          8.46       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.60 ++++          
  HEXA     58896460     0.02        0.00          9.24       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.63 ++++          
  HEXA     58896462     0.02        0.00          5.53       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.36 ++++          
  HEXA     58896463     0.01        0.00          2.52       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.41 ++++          
  HEXA     58896466     0.02        0.00          4.70       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.36 ++++          
  HEXA     58896471     0.01        0.00          3.99       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.66 ++++          
  HEXA     58896472     0.01        0.00          4.96       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.65 ++++          
  HEXA     58896484     0.01        0.00          3.97       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.66 ++++          
  HEXA     58896506     0.01        0.00          4.01       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.53 ++++          
  HEXA     58896519     0.01        0.00          3.37       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.62 ++++          
  HEXA     58896522     0.02        0.00          4.27       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.53 ++++          
  HEXA     58896524     0.02        0.00          4.29       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.53 ++++          
  HEXA     58896526     0.01        0.00          5.60       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.63 ++++          
  HEXA     58896529     0.01        0.00          3.01       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.51 ++++          
  HEXA     58896530     0.01        0.00          3.60       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.47 ++++          
  HEXA     58896532     0.01        0.00          3.54       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.47 ++++          
  HEXA     58896544     0.01        0.00          5.38       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.63 ++++          
  HEXA     58896545     0.01        0.00          3.60       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.52 ++++          
  HEXA     58896551     0.01        0.00          4.56       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.55 ++++          
  HEXA     58896553     0.01        0.00          3.39       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.52 ++++          
  HEXA     58896556     0.02        0.00          6.02       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.55 ++++          
  HEXA     58896570     0.01        0.00          8.44       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.61 ++++          
  HEXA     58896572     0.02        0.00          9.22       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.62 ++++          
  HEXA     58896573     0.02        0.00          9.22       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.62 ++++          
1                                                                              JUNE  24, 2014  MSC.NASTRAN 12/21/10   PAGE     9           
                                                                                                                                           
0                                                                                                                                          
 TEST THRESHOLD VALUES: HEX_AR =   100.00, HEX_EPLR =   0.50, HEX_EPIA =   150.00, HEX_DETJ =     0.00, HEX_WARP =     0.71                
                       (VISUAL FLAGS ARE DISPLAYED AFTER TEST VALUES THAT EXCEED THE TEST THRESHOLDS AS DISCUSSED ABOVE.)                  
 ELEMENT    ELEMENT   LONGEST    SHORTEST       ASPECT           EDGE POINT      EDGE POINT      MIN. JACOBIAN     FACE WARP               
  TYPE         ID       EDGE        EDGE         RATIO          LENGTH RATIO         ANGLE        DETERMINANT     COEFFICIENT              
  HEXA     58896575     0.01        0.00          8.44       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.61 ++++          
  HEXA     58896592     0.01        0.00          3.38       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.52 ++++          
  HEXA     58896600     0.01        0.00          3.60       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.52 ++++          
  HEXA     58896601     0.01        0.00          5.04       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.54 ++++          
  HEXA     58896613     0.01        0.00          3.54       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.47 ++++          
  HEXA     58896615     0.01        0.00          3.60       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.47 ++++          
  HEXA     58896616     0.01        0.00          3.01       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.51 ++++          
  HEXA     58896619     0.01        0.00          5.60       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.54 ++++          
  HEXA     58896621     0.02        0.00          4.23       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.42 ++++          
  HEXA     58896623     0.02        0.00          4.81       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.42 ++++          
  HEXA     58896626     0.01        0.00          3.35       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.62 ++++          
  HEXA     58896639     0.01        0.00          4.01       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.53 ++++          
  HEXA     58896661     0.01        0.00          3.90       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.66 ++++          
  HEXA     58896673     0.01        0.00          4.96       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.65 ++++          
  HEXA     58896674     0.01        0.00          3.78       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.66 ++++          
  HEXA     58896679     0.02        0.00          4.85       N/A- ONLY 8 NODE  N/A- ONLY 8 NODE       0.00              0.35 ++++          
1                                                                              JUNE  24, 2014  MSC.NASTRAN 12/21/10   PAGE    10           
                                                                                                                                           
0                                                                                                                                          
                                                                                                                                           
                                                                                                                                           
                            E L E M E N T   G E O M E T R Y   T E S T   R E S U L T S   S U M M A R Y                                      
                                        TOTAL NUMBER OF TIMES TOLERANCES WERE EXCEEDED                                                     
  ELEMENT        SKEW       ASPECT/     MINIMUM      MAXIMUM    SURFACE/FACE    OFFSET     EDGE POINT   EDGE POINT    JACOBIAN             
    TYPE       ANGLE      TAPER RATIO INTER. ANGLE INTER. ANGLE  WARP FACTOR    RATIO     LENGTH RATIO ANGLE LIMIT  DETERMINANT            
   BEAM          N/A          N/A          N/A          N/A          N/A            0          N/A          N/A          N/A               
   HEXA          N/A            0          N/A          N/A          104          N/A            0            0            0               
   PENTA         N/A            0          N/A          N/A            0          N/A            0            0            0               
                                                                                                                                           
         N/A IN THE ABOVE TABLE INDICATES TESTS THAT ARE NOT APPLICABLE TO THE ELEMENT TYPE AND WERE NOT PERFORMED.                        
         FOR ALL ELEMENTS WHERE GEOMETRY TEST RESULTS HAVE EXCEEDED TOLERANCES,                                                            
                                                                                                                                           
         HEXA     ELEMENT ID 58896343 PRODUCED SMALLEST FACE WARP FACTOR OF       0.35 (TOLERANCE =        0.71).                          
 *** USER WARNING MESSAGE 3204 (SSG1)                                                                                                      
     UNABLE TO FIND SELECTED SET (   57110) IN TABLE (SLT ) IN SUBROUTINE (SSG1).                                                          
 *** USER WARNING MESSAGE 3204 (SSG1)                                                                                                      
     UNABLE TO FIND SELECTED SET (   57112) IN TABLE (SLT ) IN SUBROUTINE (SSG1).                                                          
 *** USER WARNING MESSAGE 3204 (SSG1)                                                                                                      
     UNABLE TO FIND SELECTED SET (   57180) IN TABLE (SLT ) IN SUBROUTINE (SSG1).                                                          
 *** USER WARNING MESSAGE 3204 (SSG1)                                                                                                      
     UNABLE TO FIND SELECTED SET (   57181) IN TABLE (SLT ) IN SUBROUTINE (SSG1).                                                          
 *** USER WARNING MESSAGE 3204 (SSG1)                                                                                                      
     UNABLE TO FIND SELECTED SET (   57200) IN TABLE (SLT ) IN SUBROUTINE (SSG1).                                                          
 *** USER WARNING MESSAGE 3204 (SSG1)                                                                                                      
     UNABLE TO FIND SELECTED SET (   57500) IN TABLE (SLT ) IN SUBROUTINE (SSG1).                                                          
 *** USER WARNING MESSAGE 3204 (SSG1)                                                                                                      
     UNABLE TO FIND SELECTED SET (   57192) IN TABLE (SLT ) IN SUBROUTINE (SSG1).                                                          
 *** USER WARNING MESSAGE 3204 (SSG1)                                                                                                      
     UNABLE TO FIND SELECTED SET (   57110) IN TABLE (SLT ) IN SUBROUTINE (SSG1).                                                          
 *** USER WARNING MESSAGE 3204 (SSG1)                                                                                                      
     UNABLE TO FIND SELECTED SET (   57112) IN TABLE (SLT ) IN SUBROUTINE (SSG1).                                                          
 *** USER WARNING MESSAGE 3204 (SSG1)                                                                                                      
     UNABLE TO FIND SELECTED SET (   57180) IN TABLE (SLT ) IN SUBROUTINE (SSG1).                                                          
 *** USER WARNING MESSAGE 3204 (SSG1)                                                                                                      
     UNABLE TO FIND SELECTED SET (   57181) IN TABLE (SLT ) IN SUBROUTINE (SSG1).                                                          
 *** USER WARNING MESSAGE 3204 (SSG1)                                                                                                      
     UNABLE TO FIND SELECTED SET (   57200) IN TABLE (SLT ) IN SUBROUTINE (SSG1).                                                          
1                                                                              JUNE  24, 2014  MSC.NASTRAN 12/21/10   PAGE    11           
                                                                                                                                           
0                                                                                                                                          
0                                                                                                                                          
0                                                                                                                                          
0                                                                                                                                          
                                                                                                                                           
 *** USER WARNING MESSAGE 3204 (SSG1)                                                                                                      
     UNABLE TO FIND SELECTED SET (   57230) IN TABLE (SLT ) IN SUBROUTINE (SSG1).                                                          
 *** USER WARNING MESSAGE 3204 (SSG1)                                                                                                      
     UNABLE TO FIND SELECTED SET (   57500) IN TABLE (SLT ) IN SUBROUTINE (SSG1).                                                          
 *** USER WARNING MESSAGE 3204 (SSG1)                                                                                                      
     UNABLE TO FIND SELECTED SET (   57530) IN TABLE (SLT ) IN SUBROUTINE (SSG1).                                                          
 *** USER WARNING MESSAGE 3204 (SSG1)                                                                                                      
     UNABLE TO FIND SELECTED SET (   58303) IN TABLE (SLT ) IN SUBROUTINE (SSG1).                                                          
 *** USER WARNING MESSAGE 3204 (SSG1)                                                                                                      
     UNABLE TO FIND SELECTED SET (   58304) IN TABLE (SLT ) IN SUBROUTINE (SSG1).                                                          
 *** USER WARNING MESSAGE 3204 (SSG1)                                                                                                      
     UNABLE TO FIND SELECTED SET (   58305) IN TABLE (SLT ) IN SUBROUTINE (SSG1).                                                          
 *** USER WARNING MESSAGE 3204 (SSG1)                                                                                                      
     UNABLE TO FIND SELECTED SET (   57192) IN TABLE (SLT ) IN SUBROUTINE (SSG1).                                                          
1                                                                              JUNE  24, 2014  MSC.NASTRAN 12/21/10   PAGE    12           
                                                                                                                                           
0                                                                                                                                          
 *** USER INFORMATION MESSAGE 7310 (VECPRN)                                                                                                
     ORIGIN OF SUPERELEMENT BASIC COORDINATE SYSTEM WILL BE USED AS REFERENCE LOCATION.                                                    
     RESULTANTS ABOUT ORIGIN OF SUPERELEMENT BASIC COORDINATE SYSTEM IN SUPERELEMENT BASIC SYSTEM COORDINATES.                             
0                                                  OLOAD    RESULTANT                                                                      
  SUBCASE/    LOAD                                                                                                                         
  DAREA ID    TYPE       T1            T2            T3            R1            R2            R3                                          
0        1     FX   -3.093766E+04     ----          ----          ----       5.784622E+03 -7.216881E+03                                    
               FY       ----       3.272818E+03     ----      -7.800531E+03     ----       1.131061E+05                                    
               FZ       ----          ----       2.669954E+02  7.735908E+03 -1.532691E+04     ----                                         
               MX       ----          ----          ----       4.466352E+00     ----          ----                                         
               MY       ----          ----          ----          ----      -1.359086E+00     ----                                         
               MZ       ----          ----          ----          ----          ----       1.273146E+01                                    
             TOTALS -3.093766E+04  3.272818E+03  2.669954E+02 -6.015674E+01 -9.543644E+03  1.059020E+05                                    
0        2     FX    2.382909E+06     ----          ----          ----      -6.243828E+03  1.078259E+04                                    
               FY       ----      -6.638940E+01     ----      -1.382242E+03     ----      -1.298495E+04                                    
               FZ       ----          ----      -2.043588E+02  1.387092E+03  1.282126E+04     ----                                         
               MX       ----          ----          ----       1.097630E+00     ----          ----                                         
               MY       ----          ----          ----          ----       4.965497E-03     ----                                         
               MZ       ----          ----          ----          ----          ----      -5.295955E+00                                    
             TOTALS  2.382909E+06 -6.638940E+01 -2.043588E+02  5.947266E+00  6.577434E+03 -2.207661E+03                                    
0        3     FX   -5.205334E+04     ----          ----          ----      -3.067152E+04 -2.504951E+04                                    
               FY       ----      -2.579148E+05     ----       2.346708E+05     ----      -6.551628E+06                                    
               FZ       ----          ----       3.522443E+04  1.927350E+05 -1.032822E+06     ----                                         
               MX       ----          ----          ----      -1.224908E+01     ----          ----                                         
               MY       ----          ----          ----          ----      -3.341261E+00     ----                                         
               MZ       ----          ----          ----          ----          ----      -1.369588E+02                                    
             TOTALS -5.205334E+04 -2.579148E+05  3.522443E+04  4.273936E+05 -1.063497E+06 -6.576815E+06                                    
0        4     FX    2.382909E+06     ----          ----          ----      -6.243828E+03  1.078259E+04                                    
               FY       ----      -6.638940E+01     ----      -1.382242E+03     ----      -1.298495E+04                                    
               FZ       ----          ----      -2.043588E+02  1.387092E+03  1.282126E+04     ----                                         
               MX       ----          ----          ----       1.097630E+00     ----          ----                                         
               MY       ----          ----          ----          ----       4.965497E-03     ----                                         
               MZ       ----          ----          ----          ----          ----      -5.295955E+00                                    
             TOTALS  2.382909E+06 -6.638940E+01 -2.043588E+02  5.947266E+00  6.577434E+03 -2.207661E+03                                    
1                                                                              JUNE  24, 2014  MSC.NASTRAN 12/21/10   PAGE    13           
                                                                                                                                           
0                                                                                                                                          
 *** USER INFORMATION MESSAGE 7310 (VECPRN)                                                                                                
     ORIGIN OF SUPERELEMENT BASIC COORDINATE SYSTEM WILL BE USED AS REFERENCE LOCATION.                                                    
     RESULTANTS ABOUT ORIGIN OF SUPERELEMENT BASIC COORDINATE SYSTEM IN SUPERELEMENT BASIC SYSTEM COORDINATES.                             
0                                                  OLOAD    RESULTANT                                                                      
  SUBCASE/    LOAD                                                                                                                         
  DAREA ID    TYPE       T1            T2            T3            R1            R2            R3                                          
0       10     FX    1.457537E+06     ----          ----          ----       6.565476E+03 -7.065631E+03                                    
               FY       ----       3.294975E+03     ----      -7.801710E+03     ----       1.137743E+05                                    
               FZ       ----          ----      -2.040499E+01  7.735051E+03 -6.837568E+03     ----                                         
               MX       ----          ----          ----       4.466352E+00     ----          ----                                         
               MY       ----          ----          ----          ----      -1.359086E+00     ----                                         
               MZ       ----          ----          ----          ----          ----       1.273146E+01                                    
             TOTALS  1.457537E+06  3.294975E+03 -2.040499E+01 -6.219287E+01 -2.734512E+02  1.067214E+05                                    
0       11     FX    9.582796E+05     ----          ----          ----      -6.878315E+03  1.044271E+04                                    
               FY       ----      -2.052943E+02     ----      -1.375786E+03     ----      -1.709664E+04                                    
               FZ       ----          ----       2.929543E+01  1.373877E+03  5.924783E+03     ----                                         
               MX       ----          ----          ----       1.097630E+00     ----          ----                                         
               MY       ----          ----          ----          ----       4.965497E-03     ----                                         
               MZ       ----          ----          ----          ----          ----      -5.295955E+00                                    
             TOTALS  9.582796E+05 -2.052943E+02  2.929543E+01 -8.116455E-01 -9.535269E+02 -6.659222E+03                                    
                                                                                                                                           
 *** SYSTEM INFORMATION MESSAGE 4159 (DFMSA)                                                                                               
     THE DECOMPOSITION OF KLL      YIELDS A MAXIMUM MATRIX-TO-FACTOR-DIAGONAL RATIO OF    3.970729E+04                                     
                                                                                                                                           
 *** USER INFORMATION MESSAGE 4158 (DFMSA)                                                                                                 
 ---- STATISTICS FOR SPARSE DECOMPOSITION OF DATA BLOCK KLL      FOLLOW                                                                    
        NUMBER OF NEGATIVE TERMS ON FACTOR DIAGONAL =      1                                                                               
        MAXIMUM RATIO OF MATRIX DIAGONAL TO FACTOR DIAGONAL =  8.8E+08 AT ROW NUMBER      75953                                            
                                                                                                                                           
 *** SYSTEM INFORMATION MESSAGE 4159 (DFMSA)                                                                                               
     THE DECOMPOSITION OF KLL      YIELDS A MAXIMUM MATRIX-TO-FACTOR-DIAGONAL RATIO OF    8.799964E+08                                     
 *** USER WARNING MESSAGE 4698 (DCMPD)                                                                                                     
     STATISTICS FOR DECOMPOSITION OF MATRIX KLL.                                                                                           
     THE FOLLOWING DEGREES OF FREEDOM HAVE FACTOR DIAGONAL RATIOS GREATER THAN                                                             
     1.000000E+07 OR HAVE NEGATIVE TERMS ON THE FACTOR DIAGONAL.                                                                           
     USER INFORMATION:                                                                                                                     
     THIS MESSAGE MAY BE IGNORED IF NO GRID POINT IDS OR HIGH RATIO MESSAGES APPEAR IN THE TABLE ON THE NEXT PAGE.                         
1                                                                              JUNE  24, 2014  MSC.NASTRAN 12/21/10   PAGE    14           
                                                                                                                                           
0                                                                                                            SUBCASE 10                    
0                                                                                                                                          
         GRID POINT ID       DEGREE OF FREEDOM   MATRIX/FACTOR DIAGONAL RATIO        MATRIX DIAGONAL                                       
                                                                                                                                           
        57004426                    T1                  -8.79996E+08                   2.05308E+09                                         
        57004426                    T2                   2.05269E+08                   8.17563E+08                                         
        57004426                    T3                   5.24272E+07                   5.46972E+08                                         
 ^^^                                                                                                                                       
 ^^^ USER   FATAL   MESSAGE 9050 (SEKRRS)                                                                                                  
 ^^^ RUN TERMINATED DUE TO EXCESSIVE PIVOT RATIOS IN MATRIX KLL.                                                                           
 ^^^ USER ACTION:  CONSTRAIN MECHANISMS WITH SPCI OR SUPORTI ENTRIES OR SPECIFY PARAM,BAILOUT,-1 TO                                        
     CONTINUE THE RUN WITH MECHANISMS.                                                                                                     
1                                                                              JUNE  24, 2014  MSC.NASTRAN 12/21/10   PAGE    15           
                                                                                                                                           
0                                                                                                            SUBCASE 10                    
 * * * *  D B D I C T   P R I N T  * * * *      SUBDMAP = PRTSUM  ,  DMAP STATEMENT NO.     40

 

[jomocas]

So guys I think I found out why I get the Max Ratio fatal message.

I forgot to specify the SPC for the two buckling SCs.

Thanks a lot for your answers,

 

[nlgyro]

Thanks. it was indeed of great help.

Your static subcases are good. The matrix decomp yields a max ratio of < 1e5

Its the buckling case (subcase 10) which is the culprit.

Essentially what nastran solves for subcase10 is:

[K+Kd(preload)+lambda*Kd(buckle)]{phi} = {0}

The solution to this is only possible if [K+kd(preload)] is not positive definite, i.e structure should not buckle for the applied pre-load.

Now, I have no clue what your structure looks like or the applied loads on it, but if I were you I'll start by investigating whether the pre-load is excessive. Note excessive pre-load can result in a wrong solution or no solution.

BTW, there are UWM's complaining about missing loadsets. Maybe you have looked into this, but I just thought its worthwhile to mention this.

Good Luck!!

 

[nlgyro]

Thx. I did not notice those missing SPC's. Indeed that's what makes the [K+Kdpreload] not positive definite.