Continue to Site

Eng-Tips is the largest engineering community on the Internet

Intelligent Work Forums for Engineering Professionals

Register Log in
  • Congratulations GregLocock on being selected by the Eng-Tips community for having the most helpful posts in the forums last week. Way to Go!

Boiler and Pressure Vessel engineering

Jimjoe
  • Locked
  • Question
Is a man way to a pressure vessel a girth flange. 2
Replies
4
Views
98
r6155
r6155
Ali Haidar
  • Locked
  • Question
Nodes in PV Elite
Replies
2
Views
123
gr2vessels
gr2vessels
FPPE
  • Locked
  • Question
Ideal flange/gasket configuration for hydrogen service 2
Replies
12
Views
274
FPPE
FPPE
Sajjad2164
  • Locked
  • Question
Indirect fired heater - Mass flow rate of fuel
Replies
18
Views
190
Sajjad2164
Sajjad2164
Clement-Corri
  • Locked
  • Question
Yield Strength in ASTM Norms
Replies
4
Views
140
Clement-Corri
Clement-Corri
CSunny
  • Locked
  • Question
Validation of FEA results
Replies
2
Views
49
TGS4
TGS4
BZ29
  • Locked
  • Question
How to Support very long Pressure Vessel (Bullets) on two saddles? 6
2
Replies
35
Views
393
MJCronin
MJCronin
cknsr123
  • Locked
  • Question
ASME - oval manhole 1
Replies
8
Views
236
davefitz
davefitz
Jimjoe
  • Locked
  • Question
Man way of pressure vessel relation to girth flange 1
Replies
2
Views
95
Jimjoe
Jimjoe
Karthik P
  • Locked
  • Question
Non-Standard/Customised Flange MAWP 2
Replies
3
Views
99
LittleInch
LittleInch
sarawana
  • Locked
  • Question
cathodic protection by using pressure vessel
Replies
1
Views
37
Dhurjati Sen
Dhurjati Sen
Ilanseran Ramadass
  • Locked
  • Question
Two adjacent opening compensation while overlapping
Replies
0
Views
45
Ilanseran Ramadass
Ilanseran Ramadass
steris
  • Locked
  • Question
Repair of Grinding Gouge 2
Replies
13
Views
217
DVWE
DVWE
Santosh Ingale
  • Locked
  • Question
Hello Experts, Does any one know a 3
Replies
8
Views
115
Resegone
Resegone
fabiobs
  • Locked
  • Question
Forged brass valves
Replies
5
Views
109
bcd
bcd
Ilanseran Ramadass
  • Locked
  • Question
ASME MATERIAL NOMENCLATURE 1
Replies
3
Views
47
Ilanseran Ramadass
Ilanseran Ramadass
inammanj123
  • Locked
  • Question
Why for SA 387 GR 11, Pvelite is making PWHT mandatory, even thickness less than 16 mm ?
Replies
3
Views
57
r6155
r6155
Saver2008
  • Locked
  • Question
CAPACITY OF A PRESSURE RELIEF VALVE FOR A STEAM DRUM 2
Replies
6
Views
348
IM383
IM383
mjpetrag
  • Locked
  • Question
Brittle CS boiler tubes - hydrotesting 1
Replies
4
Views
55
mjpetrag
mjpetrag
FPPE
  • Locked
  • Question
MDMT Exemption at -45 °C for pressure components and welding specifications UCS-66/67/68
Replies
3
Views
130
FPPE
FPPE
You must log in or register to post here.

Part and Inventory Search

Sponsor

Back
Top Bottom