Search results for query: *

ok .... any doubt andre... specialist and multi axis development of IS & V and postprocessors member committee nxcam plm world skype:andrenxcam7

hi exactly you should schedule with only one part zero if not properly generate the coordinates or can be post processor or programming was not done correctly always local and never use the main program should run on top of a single part zero to be a program of 4 or 5 axis any doubt...

use only main not use local andre... specialist and multi axis development of IS & V and postprocessors member committee nxcam plm world skype:andrenxcam7

use only main not the place specialist and multi axis development of IS & V and postprocessors member committee nxcam plm world skype:andrenxcam7

thanks jarek..... if you need training by the skipe or doubt about variable contour or multi axis be just speak..... André... specialist and multi axis development of IS & V and postprocessors member committee nxcam plm world skype:andrenxcam7

hi friend if you are new to nx must take training and a very advanced comndo use the variable contour and the easiest and fastest sequential mill worked in secotools muitosanos and machined straight helices asim. any doubts ... follows the file ... with machining. andrenxcam@yahoo.com.br...

had a similar problem ... nx6 installed the complete software + license and the nx7.5 I just created a service on the flex and ran smoothly nx7.5 is a difference between flex nx6 the manufacturer and macrovision and nx7.5 and Acresso I personally prefer to the Macrovision at least it...

hello jeff select the walls that you want to generate the machining and machining the tool will go through the profile following the floor not necessary to take the rays of the models also select them and an excellent command to be used in machining of this type I've used and recommend. I...

hi you can send me the file for me to check some custom comand was not created or loaded awaiting Andre specialist and multi axis development of IS & V and postprocessors member committee nxcam plm world skype:andrenxcam7

sorry format numerical wrong !! specialist and multi axis development of IS & V and postprocessors member committee nxcam plm world skype:andrenxcam7

hi igor this possible !!! depends where you would and what if the command iTNC 530 manages def cycle 32 can only be placed in the function def cycle 32 ... you can do so thinning INTOL 00:12 00:03 outtol put the media in the cycle def just pre INTOL 00:05 00:05 outtol the same thing just...

igor !!!!! i see email understand you want put compensation i go fix the sent you i go sent you Andre specialist and multi axis development of IS & V and postprocessors member committee nxcam plm world skype:andrenxcam7

hi igor !!!!! igor should let the broker tool "0" because the software is already compensating Now if you want to compensate with the effective radius of the cutter have to set the output compensation cuting contact traking milling time she goes over the profile but offset radius of 5 mm Andre...

[ponder] specialist and multi axis development of IS & V and postprocessors member committee nxcam plm world skype:andrenxcam7

hi caphook send me your file helps you stop it Andre... or report GTAC ;... specialist and multi axis development of IS & V and postprocessors member committee nxcam plm world skype:andrenxcam7

hi igor I will be on line at 18:00 of Brazil skype if you want to talk Andre specialist and multi axis development of IS & V and postprocessors member committee nxcam plm world skype:andrenxcam7

hi igor you have go to word sequence in post builder the put the "F" after of the dr you tested post I sent you you like of the post the arcs without wrongs André specialist and multi axis development of IS & V and postprocessors member committee nxcam plm world skype:andrenxcam7

hi send me a part i go show how to it hug !!!! André specialist and multi axis development of IS & V and postprocessors member committee nxcam plm world skype:andrenxcam7

hi john sorry forget of the put %.2f thanks.... sorry igor.. André specialist and multi axis development of IS & V and postprocessors member committee nxcam plm world skype:andrenxcam7

friend nxcam changed much your exit strategy tools was not like now moves non cuting this more complete understand their difficulty GTAC but will not help you also work with 5 axis and at first it was hard but I soon adapted you recommend a course of upgrading NX7 because at nx 07/05 has not...