Search results for query: *

Thank you very much SW and Blas for your time and awesome answers ! I've read many of your articles in your blog Blas, they are magnificent. And as a Spanish speaker most of them are even easier to understand.

Helllo all, I'll post two different questions in a same thread. ----------------------------------------------------------------------------- Question 1 I have made several fastener connections in a model, through spider RBE3s and the fastener represented by a RBE2. I leave an image so you...

Hello, I hope you are doing well. I have some questions concerning HEX mesh. My idea is to mesh a pin with HEX elements. I divided the fairly simple geometry into three cylinders, so it can be easily HEX meshed (without using the HEXMesh Bodies feature of FEMAP). I'll leave an image of the...

Hello, I am using RBE2 elements to represent bolts that link three plates together. The dependent node is in the top plate (where the load comes from) and the other two dependent nodes is one in each one of the bottom plates. I leave an image below so it is easier to understand. I have...

Hello, I am analyzing a structure that it's going to be transported by road and by airplane. Following standards we saw that normally for these transports the structure shall support at maximum 2.2g in all directions. Hence, the structure was designed to withstand up to 3g (4g in best-case...

Monsieur you deserve the heaven haha Thanks !

Hello all, Quick and stupid question : Why FEMAP has such awful colors ? Besides that, does anyone know a way to modify the color of the borders of the elements ? Because, as you can see in the image below, I select a blue color for the elements but FEMAP says "okay, I am gonna put an AWFUL...

Thank you both for your answers ! They were really useful. Cordially, EC

Hello, I would like to start a discussion about the best way (mesh quality vs number of elements vs results accuracy) to mesh a large plate with a lot of small holes. The thing is that I have a large plate (2000 [mm] x 1350 [mm]) which contains a lot of small holes (diameter 3.2 [mm], see...

Thank you very much Blas ! It was the thing that was missing.

Hello, I hope you are well. In the model I'm working with, I have to simulate a plate that rests over some rollers. Then, I want to simulate the rollers as constraints that only block the displacement in one sense for a given direction, i.e., for -Z the movement is constrained, but for +Z the...

Thank you both very much for the your answers and the time you took responding to this topic. I have three questions that come to my mind after reading the thread : 1. Why does the Max Principal Stress not give the correct curve ? In my opinion it should as is always taking the maximum normal...

Hello rb1957, Thanks for your answer. I looked at both. I could run the analysis with a linear material, but I have no interest in doing so because I need the material to undergo plasticity.

Hello, I hope you are doing well. I am doing a burst analysis of a vessel. Consequently, NL material has to be introduced. Hence, I introduced the stress-strain curve and selected the Plasticity NL option. I followed what the NX Nastran's manual says : The first point of the curve is (0,0)...

Hello, I hope you are doing well. On one hand (Symmetry BCs in presured vessel) : I have been strugling for a while, thinking about the proper way to define the symmetry conditions for the model I am studying. It is a simple pressured vessel, then, as it is symmetrical, I am analyzing a...

Thank you very much for your responses. I continued working with a symmetrical model, which is way better from all prespective points. I improved the geometry and the mesh is all mapped. Thanks !

Hello, I hope you are doing well. I am analyzing a tank, and the idea is to simulate a burst test. Below I leave an image of the tank. The thing is that I would like to study it as if it was floating in the space, i.e., analyze only the pressure and neglect the effect of the necessary...

Yes, the fillet is part of the original 3D part. I directly imported it from CATIA. Then, if I hide (with the checkbox) the solid component, the surface disappears with the rest of it, then I think it is still the same component, and included in the 3D part. In other words, it has not created a...

Hello, I hope you are doing well. I started using FEMAP a couple months ago. Before I used HyperMesh as pre-processor. I am doing some geometry cleanup, more precisely, removing a hole. The problem is that the hole was in the intersection of two surfaces (a fillet). Consequently, when I tried...