Search results for query: *

Not your problem, you can explain it more detailed?

Apparently the encoder is faulty. Fanuc get one for replacement. This machine takes us crazy!

Hello, They can advise on this alarm? 350z spc alarm z axis pulse coder Machine laser: Amada 1212alphaII - 1995. thanks!

Hello Friends, like a laser no problems now all sorted. LASER NINJA, the filter is new. Today I bring a new pump for the chiller everything was solved! Thank you!

Hello LASER NINJA: That the significance of the code C009? (Turbo blower) The key "T" is all closed!. I still doubt the defective pump Thanks for your help!

FOOSTRAP - LASERNIJA Hello Friends! I happened to have the tasks and findings in the cooling system: 1 - The turbo blower is TYPE A04B-0800-C009 Date 07/2005. 2 - Change the oil kit FANUC (A04B-0800K329 # 1 - expiration date 03/2015). The oil had not taken any kind of particles or traces. From...

FOOSTRAP The oil used is the original FANUC LASERNINJA Today laser remove the cover and discovered that the inlet hose to the turbo blower was cold, but the most noticeable is that the output was very hot. It is possible that beyond a blockage of cooling water. I could not disarm because I was...

Hello friends, my turbo blower is throwing an alarm low oil level. The oil level display is within normal parameters .... which can happen??

Hi I have a short 1500w and very well these thicknesses. The secret of good cut is: -Check that the lens is clean and 7.5 " -Check that the beam is centered on the nose output -Check that the priece pass the sheet before you start cutting, if there is dotted because the blade passage, increase...

Hi all, I have a refrigeration unit KOOLANT KOOLERS a 2HP water pump, which is the PSI you have to have laser system? (AMADA LC1212 AII - year1995 - C1500B) Now that value was 30PSI right? I await answers greetings to my friends!

Thanks Friends, today I try! ... after I tell them how I was! It is common to pass this type of failure, or operate something wrong?

Today, we perform the test of vacuum pump, the system disconnected and tested with a vacuum gauge and makes an absolute vacuum, so is ruled malfunction. Connecting all again the value of 270 rose to 480, apparently a large leak. I was reviewing the tubes and naked eye cracks are not observed. I...

....sorry I forgot the laser machine is AMADA LASMAC1212 AlphaII - C1500B - Year 1995.

Hello to all my friends on the forum, Today when I turned on the laser to reach the sequence number 17 stops longer than normal and the alarm appears 4080. The vacuum value before starting the laser is 905, when the sequence reaches number 17 empty value reaches 270, there appears after the...

Hello again! We had an accident, the "Y" Axis collided with a device. The zero point is lost. Controlling measures 14 millimeters see that'm moved. Apparently turning the motor elastic coupling. Right now we are working discounting adding 14 mm to the function G98 (and move the limit swtich)...

Someone with more suggestions????

Hello, I suffered with the same alarm, in our case there was one source of power was damaged. Technicians removed and replaced the circuitry and power diodes.(Resonator) You must call AMADA technician. I hope it will answer. Luck!

Hello, I have a LC1212-AlphaII - 1500wats. I have to cut stainless steel 1 mm thick vinyl protection. I have many problems of formation of high pressure balloon with shop air. You must have the vinyl because after cutting continues bending. Another problem is that while cutting passes from...

Friends Thanks for the responses I have been very useful!

When we cut steel (SAE1010) 1.6mm thick, as the tips do not burn? especially where there are pieces with slots little room, if I go burn rate if we lower the speed and frequency is as a saw ... is a real issue! The problem is that my machine did not bring all cutting boards charged in NC, and...